Noise Control
Soundproofing
Acoustical Enclosures
Acoustical Curtain Enclosures
Acoustical Foam Barriers
Acoustical Services
Noise Barriers
Acoustical Foam
Sound Absorbers
ArtUSA University
ArtUSA Gallery
Product Spec Sheets
|
ArtUSA Noise Control Products Inc.
We are noise pollution solution providers. By offering engineering, fabrication and installation of the absolute best noise reduction and noise control products available our company has set the bar in the soundproofing industry. Sound-proofing is our passion. We design, fabricate and install acoustical panels, acoustical insulation, sound barriers, acoustical wall panels, sound-barriers, noise barrier, sound enclosures, acoustic insulation, noise barriers, sound proofing and sound barriers.
| ArtUSA Acousti-Wall Installation Guide for
Noise and Sound Control Panels |
ArtUSA Acousti Wall Panels have
a lightweight foam core and are simple to install
with a wide range of methods. The panels attach in
seconds to existing, clean surfaces. Choose from the
mounting options below. |
| Foam Adhesive installation: |
|
Clean wall surface.
Apply 1/4" bead of adhesive
around panel perimeter on
the fiberglass edge.
Apply a 1/4" bead from corner to
corner through the center to create an "X."
Press panel to surface for 5
seconds
Pull the panel away for approximately 1 minute to
allow adhesive to become tacky.
Firmly press panel back into
position.
AcouSTIC
adhesive (part number PA-02) is a non-toxic,
water-based adhesive that cleans up with soap and
water. Each 10.5 ounce tube installs approximately 32
square feet of product. Tubes fit standard caulking
guns or can be used with ArtUSA’s applicator
gun. |
| |
|
| Hook & Loop Fastener
Installation: |
 |
Prior to shipping, the loop side of the fastener is
attached to the panel. The hook side is connected to
the loop and has a tape backing. To install, just
remove the tape backing and position the panel
against the wall. |
| |
|
| Concealed Spline Installation: |
 |
Panels come
with kerfs along the panel edges and are equipped
with a concealed spline attachment. The spline is
inserted into one of the panels and installed on the
wall. Connecting panels are inserted into the other
half of the spline. |
| |
| Z Clip Installation: |
 |
Before
shipment, special Z clips are mounted to the back of
the panel. Corresponding wall clips or wall bars are
installed on the wall at the appropriate location to
allow attachment of the panel. |
 |
 |
 |
 |
 |
ABSORPTIVE
High performance
absorption. |
HIGH
IMPACT
Absorptive in high traffic areas. |
REFLECTIVE
For combined use in Studios for
absorption and reflection. |
MINERAL
CORE
multi-purpose panel for absorption
and sound blocking |
ABUSE
RESISTANT
For gymnasiums, absorption and abuse
resistance. |
 |
 |
 |
 |
|
TACKABLE
1
For long lasting and effective
tackability. |
HI-TACK
High absorption and tackability |
Tackability 2
Tackability where sound absorption
is not necessary. |
NOISE
BARRIER
B-10-NR vinyl barrier, ideal for
areas requiring high STC.
|
|
ArtUSA
Acousti-Panels: Sound Absorption
Coefficients
|
7 PCF Glass Fiber |
125Hz |
250Hz |
500Hz |
1KHz |
2KHz |
4KHz |
NRC |
1"
2"
|
.29
.13
|
.26
.74
|
.76
1.23
|
1.09
1.26
|
1.21
1.25
|
1.09
1.18
|
.85
1.10
|
|
Square |
Radius |
Bevel |
Half Bevel |
|
Impaling
Clips:
Note: In the pictures below, the
adhesive necessary for permanent
installation is not shown. Put a
bead of PSA-29 panel adhesive around
the perimeter of the back of the
panel – approx ¼” bead, as well as a
few locations on the back of the
panel that will touch the wall
between the impaling clips. |
 |
 |
 |
 |
| Glue
or screw impaling clip to the wall
and allow to dry completely. |
Align
panel and impaling clips so that
impaling clip touches the fiberglass
rather than the fabric wrapped
around the back of the panel. |
Begin
to press impaling clips into the
back of the panel. |
Press
panel all the way onto the impaling
clip so the panel is touching the
wall making sure that the panel is
pressed completely on to each of the
impaling clips. |
Mechanical Clips
(ie. E.C. clips / E.Z. Clips)
 |
 |
 |
| Wall
bars attaches to wall with standard
screws (not shown) provided by
others. |
Panel
clips will be adhered into the back
of the panel with epoxy as needed
during production. |
Wall
Bar and panel clip slide together to
support the weight of the acoustical
panel. |
|
|
|
We
manufacture or package, sell, and install - Sound
Enclosures - Equipment Enclosures - Personnel Enclosure
- Barrier Walls -Thermal Enclosures - Audiometric
Testing Rooms - Punch Press Enclosure - Test Cells -
Clean Rooms - Diesel Generator & Positive Displacement
Enclosures - Fiberglass Enclosure - In-plant Space -
Curtain Enclosures - Acoustical Pipe and Duct Lagging -
Sanitary Panels and Baffles - Portable Screens - Damping
Compound - Industrial Ceiling Baffles - Class 1 Fire
Rated Foams - Polyurethane Foams - Fiber-Free - Adhesive
Backed - Facings and Barriers - SONEX - Sound Seal -
Acoustical Curtains - Acoustical Foam - Rectangular
Silencers - Round Silencers - Elbow Silencers - Dust
Collectors - Fume Oxidizers - Oil Mist Collectors -
Smoke Capture - Work Stations - Isolation Mounts - Pads
- Levelers Architectural Noise Control / Noise Abatement
- Fabric and Decorative Foam Panels - Baffles -
Deflectors - Curtains - Banners Dosimeters - Calibrators
- Real Time Analyzers - Software - Active Noise
Canceling Muffs - Noiseless Metals
|
